In industries such as pharmaceuticals, food, flavorings, and fine chemicals, optical rotation is a common analytical parameter. By measuring how a substance rotates polarized light, one can assess its optical properties, providing essential data for quality control, quantitative analysis, and the evaluation of product consistency.

When a beam of plane-polarized light passes through an optically active substance, its plane of polarization is rotated by a certain angle. This angle of rotation is known as the optical rotation (or angle of optical rotation), typically denoted by the symbol α and measured in degrees (°). The optical rotation depends on factors such as the composition of the sample, its concentration, the path length of the light, the measurement temperature, and the wavelength of the light source. Based on the direction in which the plane of polarized light is rotated, optically active substances are classified as either dextrorotatory (right-rotating) or levorotatory (left-rotating), with the measurement results indicated by a positive sign (+) or a negative sign (−), respectively.

Testing requirements for optical rotation vary across different industries. The following three national standards serve as representative references for such testing.
This standard specifies a polarimetric method for determining the starch content in native starch, applicable to native starch samples that fall within its defined scope. The general procedure involves specific sample preparation steps, followed by measuring the optical rotation of the resulting solution and calculating the starch content. This method is not suitable for all starch products; for instance, native starches with high amylose content, modified starches, and pregelatinized starches are outside its scope.
Application Areas: Native starch production, testing of food raw materials, and related quality control.
This standard specifies methods for determining the optical rotation of fragrances, applicable to fragrance samples that exhibit optical activity. For certain liquid fragrances, measurements can be performed directly under the conditions specified in the standard. For samples that are solid or semi-solid at room temperature, or those with high viscosity or deep color, the standard requires that they be prepared into a solution before measurement. Optical rotation data can be used to evaluate the quality of fragrances and analyze batch-to-batch consistency.
Application Areas: Production of fragrances and flavors, testing of natural fragrances, and fine chemical industry.
This standard specifies a polarimetric method for determining the starch content in animal feed. It is applicable to various types of feed, including feed raw materials, compound feeds, concentrated feed supplements, feed concentrates, and additive premixes. The underlying principle involves preparing the sample according to specified procedures to convert the starch into a measurable solution. A polarimeter is then used to determine the optical rotation of this solution, and the starch content is calculated based on the results. It should be noted that this standard is not applicable to samples containing other optically active interfering substances, nor to starch samples with an amylose content exceeding 40%.
Fields of application: Feed production, testing of feed raw materials, animal nutrition research, and feed quality control.
Optical rotation is typically measured using a polarimeter. Taking the CHNSpec DS-P900T fully automatic high-speed polarimeter as an example, the basic operating procedure is as follows:
Sample: Prepare the sample for testing in accordance with the relevant standard requirements. If the sample requires dilution or dissolution, use the specified solvent and accurately record all pertinent information.
Polarimeter tube: Select a polarimeter tube with an appropriate path length based on the testing requirements; common specifications include 100 mm and 200 mm. Since the path length affects the measured angle of rotation, a temperature-controlled polarimeter tube may be used if the sample is sensitive to temperature.
Instrument: Connect the power supply and turn on the instrument. Allow the instrument to warm up for ten minutes before proceeding with measurements.

QA personnel can log in to their QA account, navigate to the method management interface by clicking "Method" on the main screen, and select "New." After entering the method name, measurement parameters, test tube length, and other relevant data, click "Confirm" to save the method. Once saved, it can be directly accessed and used by an Operator (Op) account.

The operator can log in to their account, click "Calibration" to access the calibration interface, and select "Zero-point Calibration." Open the measurement chamber, insert a polarimeter tube containing a blank solvent (distilled water)—ensure the use of a 100 mm polarimeter tube, as required for the samples to be measured—close the chamber door, and click "Start Calibration." A notification will appear once the calibration is successfully completed.

Unscrew either end of the polarimeter tube and use a dropper to fill it with the sample solution to be tested. The raised section in the middle of the tube serves as a bubble trap; ensure that any air bubbles are contained within this trap. Do not allow bubbles to remain in the light path, as they may interfere with the measurement results. Place the polarimeter tube securely into the sample chamber and close the chamber lid. Select your pre-configured measurement parameters via "Parameter Settings" > "Measurement Method," then click "Start Measurement" to begin.

Once a measurement is complete, the relevant data—including the current measured value (optical rotation), temperature, measurement method, and final results—can be viewed directly on the device. Users can also access a "Curve Plot" to visualize the measurement curve. Furthermore, saved data can be retrieved or exported, supporting the data analysis and archiving requirements of manufacturing enterprises.

To address laboratory requirements for polarimetric analysis, CHNSpec has introduced the DS-P900T fully automatic high-speed polarimeter, designed for applications in pharmaceuticals, food, fragrances, chemical reagents, and scientific research laboratories.
The DS-P900T utilizes the 589 nm sodium D-line for measurements, offering a minimum reading resolution of 0.0001°, a zero-point repeatability of ≤0.0004°, and a relative error of ≤0.003°. It provides high-resolution readings and stable performance, making it ideal for samples with subtle optical rotation changes that require multiple repeated measurements.
Since optical rotation is highly sensitive to temperature, the DS-P900T features a temperature control system (10–60°C) with an accuracy of ±0.1°C. This capability supports samples requiring constant-temperature analysis, effectively reducing measurement discrepancies caused by temperature fluctuations.
Certain dark-colored fragrances, chemical reagents, or highly concentrated samples exhibit low light transmittance, placing higher demands on a polarimeter’s detection capabilities. The DS-P900T can operate with sample transmittances as low as 0.01%, expanding the range of measurable low-transmittance samples. In practice, users should evaluate the optical properties of the sample and relevant standards to determine whether dilution or other forms of sample pretreatment are necessary.
The DS-P900T supports fully automatic operation, with a full-scale response speed of 8°/s—enabling six measurements to be completed in approximately 26 seconds. Equipped with a 10.1-inch IPS touchscreen, the instrument allows for seamless parameter configuration, method selection, and data review, eliminating the need for traditional manual reading procedures.
The instrument supports various measurement modes—including optical rotation, specific rotation, concentration, the International Sugar Scale (°Z), and user-defined parameters—allowing for selection based on specific samples and testing requirements. The DS-P900T also enables the creation of up to 1,500 custom measurement methods. It offers an optional FDA audit trail software package, featuring four-level password-protected access control, support for 1,000 individual users, and electronic signature capabilities—providing essential tools for laboratories with strict data management and traceability requirements.
Optical rotation measurement requires more than just focusing on instrument-generated data; it necessitates a comprehensive consideration of sample state, optical path length, temperature conditions, and relevant testing standards. Standards such as GB/T 20378-2006, GB/T 14454.5-2008, and GB/T 20194-2018 provide the methodological basis for testing native starch, fragrances, and animal feed, respectively. In practical applications, selecting the appropriate test method—combined with a polarimeter equipped with automated measurement, constant-temperature control, and data management features—helps enhance laboratory operational efficiency and the consistency of measurement results. The CHNSpec DS-P900T fully automatic, high-speed polarimeter provides robust instrumentation for optical rotation measurements across diverse fields, meeting the varied testing needs of laboratories and helping organizations improve both the efficiency of their quality inspections and the standard of their data management.